What\’s New in Mastercam – PDF Drive

Most of our internal systems utilize dual monitors and we find this to be a more productive setup. Mastercam displays on the primary monitor while applications such as Mastercam Simulator, Code Expert, or Tool Manager display on the secondary monitor. Mastercam will run on lower resolution screens but beware of potential sizing issues with larger dialog boxes and panels which may be awkward to work with.

Lower resolution monitors may work fine as a second monitor in a dual screen setup. Mastercam will run on large format displays, including 4K monitors and high-DPI devices however, we do experience some display issues with these configurations.

We have found that one of the best computer upgrades is to invest in a NVMe drive. These drives are now priced at a point which makes them a good investment. Many of our test systems employ a smaller primary NVMe drive for the OS and installed applications with a second large capacity conventional drive for data.

A 3D mouse improves the way you interact with your 3D application. It is designed to be used by your non-dominant hand in tandem with a standard mouse for a balanced and cooperative work style. This chapter deals with how to create basic wireframe geometry types listed in the table above. Once you understand these, it will be easy for you to create other types. Figure: 13 shows the commands used to create wireframe geometry. The commands are arranged in groups based on entity types or specific activity.

The groups are displayed in the ribbon from basic to more complex functions. A line can start and end anywhere in the Mastercam Coordinate System as shownFigure: Full length of the line, regardless of the view.

If the line lies in the same plane that it is being viewed, the 2D and 3D lengths are the same. The angle of a line is measured from the position. Counterclockwise CCW angles are positive.

Clockwise CW angles are negative. A line that splits two other lines equally. The coordinates of the either end of a line. A line along or parallel to the X-axis.

Point equidistant from the end points. A series of lines that are connected. A line offset an equal distance from another line. A line 90 degrees to another line or arc. Sometimes referred to as a normal line. A line defined by its start point, length and angle. Lines have a direction. The Start point is the x,y,z coordinates of the first endpoint. A line that intersects an arc or spline at one point only.

A line along or parallel to the Y-axis. Figure: 15 Perpendicular Perpendicular lines pierce a line or curve at a 90 degree angle all around as shown in Figure: In other words, a perpendicular line is a tangent line rotated 90 degrees.

This type of line is also called a Normal line when referring to arcs, splines, or surfaces. Mastercam can create a perpendicular line passing through some point on the curve or a point in space. Mastercam can define a parallel line given an offset distance from an existing line or a through point. Figure: 17 Bisecting Bisecting lines split the angle between two existing lines equally as shown in Figure: Mastercam shows multiple solutions and prompts you to select the one you want.

Figure: 18 Note: Mathematically, a line has length but no width; it is infinitely thin. When viewed directly along its axis, a line disappears. A line is sometimes referred to as a \”straight curve\”. A line is a 3D entity; it does not have to lie in a 2D construction plane to exist. Creates a line parallel to an existing line. Creates a line perpendicular to a line, arc, or spline. Creates a line representing the shortest distance between two entities. Creates a bisecting line; a line that splits the angle between two lines equally.

Creates a line tangent to an arc or spline. Requires the tangent point. We do not recommend or support the use of onboard graphics found with some PC configurations. These do not generally have the capability to drive graphics intensive applications such as Mastercam and can lead to system instability. Make sure you are using up-to-date drivers from your card manufacturer. We often see issues that are resolved with updated video drivers.

The driver version can have a great impact on how the card performs. We recommend using the automatic detect feature to detect which video card is installed. More information on configuring the graphics card can be found at this Mastercam knowledge base article.

Most of our internal systems utilize dual monitors and we find this to be a more productive setup. Mastercam displays on the primary monitor while applications such as Mastercam Simulator, Code Expert, or Tool Manager display on the secondary monitor.

Mastercam will run on lower resolution screens but beware of potential sizing issues with larger dialog boxes and panels which may be awkward to work with. To change this behavior, deselect Assign Level names to match Solid names on the Converters page of System Configuration. Mastercam organizes the various solid bodies of an assembly in the Solids Manager. Whenever possible, Mastercam names each imported solid body. Multiple bodies with the same name will have numbers appended.

Bodies in separate part files in assemblies will include the name of the assembly in the Solids Manager. Ignore blanked entities in count Select Ignore blanked entities in count from the Display options dropdown to not include blanked entities in the Entities column count. This option is off by default. Previously, blanked entities were included in the entity count and caused confusion between the count and visible entities on a level.

Import via drag and drop You can now drag and drop a supported file for example,. Mastercam Simulator Listed below are enhancements made to Mastercam Simulator, accessed through the Toolpaths Manager. You can add a bookmark, clear a bookmark, or clear all bookmarks. Use Automatic Bookmark to insert bookmarks at certain locations, such as a tool change or operation change. The bookmarks are then displayed on the playback bar. Simply select any bookmark icon to display the part as it is at that moment.

You can also use Create Bookmark on the playback bar to add a bookmark. If you exit Mastercam Simulator or regenerate the toolpaths, the bookmarks are cleared automatically. They do not persist between sessions. Create presentation You can now create a presentation from Mastercam Simulator. Saving a presentation lets you preserve your settings and layout of your Mastercam 30 What\’s New in Mastercam — General Enhancements Simulator session and can be used to show a simulation on any computer, even if it does not have Mastercam.

Select Save Presentation on the Home tab to create your presentation. Select Verify from the Toolpaths Manager, and select Simulation on the Home tab to view the machine simulation. Use the Components tab to set up stock and fixtures. Use the Data tab to set tolerances. Use the Simulation tab to set the machine, position, and tolerance. If you do not have a machine selected when entering Mastercam Simulator, Mastercam will default to a generic machine or a machine that was selected in the Machine Simulation dialog box for the standalone Machine Simulation.

Once logged in, you have access to Mastercam\’s social media outlets, your Reseller information, the Mastercam forum, and other helpful information. Alternately, you can select a member of the group, which will select the entire group.

This new option is located on the Nesting Configuration dialog box. New location for temporary files Temporary nesting files now go into Mastercam\’s default temp folder When creating a new plane by using the on-screen, dynamic gnomon, from the Planes Manager, using Trim to Plane, etc.

When editing an existing plane, the Edit Plane function panel opens. The function panels share the same controls, which are enabled or disabled as appropriate for the current mode.

Import via drag and drop You can now drag and drop a supported file onto the Planes Manager to import the file\’s planes. The Plane Selection dialog box displays and lets you select which planes to import. The planes are imported into the open Mastercam file. To ensure that Mastercam does not overwrite your part, machine, and control definition files, the save file workflow has been changed.

Mastercam part files When you open a Mastercam X9 or older part file in Mastercam , selecting Save opens the Save As dialog box, where you can save the file with the When you open a Mastercam part file in , you will see a warning banner in the interface that tells you the file is from a previous version of Mastercam.

If you click Save, a warning will display. Choosing Yes saves the file as a Mastercam You can now select different types of entities without switching between Standard and Solid modes on the Selection Bar. If both the Face and Body Selection filters are 46 What\’s New in Mastercam — General Enhancements enabled, the cursor will alternate between face and body selection when moving over a solid.

Mastercam displays a prompt to guide you through selection techniques. Hovering over a solid highlights the nearest face and displays the face selection cursor. Click to select a solid face or double-click to select a feature. If only the Face Selection filter is enabled, you can triple-click to select all faces of a solid body. Click an individual face of the solid to deselect it from the body. Pressing [Esc] or double-clicking in an open area of the graphics window accepts the selection.

Selection masking for sheet bodies A new sheet solid selection capability has been added to the Select All and Select Only dialog boxes. Select Level or Viewsheet on the Capture Images dialog box to include them into your report. Click an icon to launch the website.

System Configuration Listed below are enhancements made to System Configuration. Default file open type You can set a default file type to be used when opening a file. The setting persists from session to session. Update to Parasolids Prototek plans to expand its rapid prototype capabilities via acquisition of Wisconsin-based Prototype Solutions Group.

Stratasys will expand its differentiated materials offering in stereolithography, DLP, and powders, company reports. Metal 3D printing is a high energy process in which it is possible for unmanaged By Admin.

If you delete or undo a. To delete unwanted geometry, select the geometry first and then press Delete from the keyboard. To zoom or un-zoom, move the cursor in the center of the geometry and scroll up or down the mouse wheel. In this step, you will create circles for which you know the diameter and the locations. To use Circle Center Point, you need to know the center point and the radius or the diameter of the circle. To complete this step, you will need to know the Cartesian Coordinate System.

A Cartesian Coordinate System is a coordinate system that specifies each point uniquely in a plane by a pair of numerical coordinates, which are the signed distances from the point to two fixed perpendicular directed lines, measured in the same unit of length as shown in Figure: 3. Figure: 3. NOTE: When entering the coordinates for the center point, the first value is the X coordinate value, then the Y value followed by the Z value only if it is different from zero.

The coordinate values are separated with commas. You do not need to use the coordinate labels if you enter the values in this order. In this step, you will use the same Circle Center Point to create circles that you know the diameters and the locations. In Mastercam, you select a Machine Definition before creating any toolpath. It acts like a template for setting up your machine. For a Mill Essentials exercise 2D toolpaths , we need just a basic machine definition. Default program number is used to enter a number if your machine requires a number for a program name.

Assign tool numbers sequentially allows you to overwrite the tool number from the library with the next available tool number. First operation tool number 1; second operation tool number 2, etc. Warn of duplicate tool numbers allows you to get a warning if you enter two tools with the same number. Override defaults with modal values enables the system to keep the values that you enter.

Feed Calculation set to From tool uses feed rate, plunge rate, retract rate, and spindle speed from the tool definition. Make sure that the rest of the parameters are as shown in Figure: 7. Figure: 7. The X, Y, Z values in the graphics area are the dimensions of the stock model. They are always positive values. The Stock Origin values adjust the positioning of the stock, ensuring that you have an equal amount of extra stock around the finished part.

The default position is the middle of the stock. Display options allow you to set the stock as Wireframe and to fit the stock to the screen. Fit Screen. NOTE: The stock model that you create is used when viewing the file or the toolpaths, during backplot, or while verifying toolpaths.

❿
 
 

❿

Mastercam 2018 whats new pdf free.System Requirements

 
Circle Center Point. 2D HS Core Mill Toolpath. Arc Tangent to 1 Entity. 2D HS Blend Mill Toolpath. Line Parallel. 2D HS Peel Mill Toolpath. Chamfer. Line Polar. Log in at replace.me to find the following downloads: Mastercam; Mastercam for SOLIDWORKS. Some downloads require you to link your account–please see. To order more books: Call or Visit replace.me or Contact that Mastercam manages for you, what you see on the computer screen is a. Adobe premiere pro cs5 5 family serial number free · Harry potter game for Free whatsapp for windows 10 · Autodesk revit user guide pdf free. How to Change Your Mind: What the New Science of Psychedelics Teaches Us About Consciousness How CNC PROGRAMMING – Mastercam.❿
 
 

❿